Turn signals (indicators) are legally required on every Toyota Tundra.
It’s a safety instrument both for you and others on the road. If you drive your Tundra without an indicator light, police will give you a ticket.
This article will discuss why your Tundra’s turn signal is not working and the diagnosis and its working fix.
There are two ways you will understand your Tundra’s turn signal not working.
- When you put left or right indicators, you will hear a fast clicking sound.
- On some models, no sound will come out of the dash speaker.
Let’s first observe the turn signal wiring diagram for the Toyota Tundra below —
The instrument panel junction box controls all the four turn signals — front left, front right, rear left, and rear right. However, the junction box isn’t directly connected to the lights. Some fuses protect these lights from surge currents.
Please turn on the hazard lights in your Tundra. All the four turn signals should flash. Now go out of your vehicle, observe each bulb, and isolate our non-working turn signal.
If only one turn signal bulb is not working, then our fix is easier than if two turn signals on the same side — drivers or passengers — don’t work.
From the above wiring diagram, we can see that all of the four turn lights are controlled by different wires.
Here are the reasons why the indicators are not working and its fix.
Turn Signal Bulb Have Burnt Out
One of the primary reasons the Toyota Tundra indicators are not working is that the lights have gone out.
Depending on the model, Toyota uses either halogen or LED light bulbs. Even though LEDs last longer than halogen bulbs, both will eventually fail due to aging.
If the lights have gone out, the fix is easy. We have to replace the bulb.
Replacing the turn signal bulb is easy. However, if you don’t feel comfortable doing some DIY, please take your Tundra to a Toyota service center or your trusted auto mechanic shop.
The cost to replace the turn signal lights at a Toyota service center typically costs $70, but at your local mechanic shop, it would cost $20-$30.
However, replacing the bulb is straightforward.
Toyota Tundra has the following specifications for turn signal bulbs:
- Front turn signal bulb No. 7444NA, W 28/8, Type B (Amber)
- Rear turn signal bulb No. WY21W, W 21, Type B (Amber)
Fuse Has Blown Out
If you see that multiple turn signal bulbs in your Toyota Tundra aren’t working, the hazard lights are not working at all, or no sounds are coming while you put left or right indicators, your turn signal fuse has gone out.
There are two fuse boxes on a Toyota Tundra. One is inside your vehicle below the steering wheel column. Another is outside of the Tundra in the engine compartment.
The inside fuse box typically controls all the lighting and electricals that are inside your Tundra.
The engine compartment fuse box controls all the lights, alternators, starters, spark plug ignition, turn signal, and other electricals outside the Tundra.
In the Toyota Tundra, the image below shows the fuse box. Typically it’s on the right side of the vehicle in the engine compartment, but on some models, it could be on the left side. The fuse box should have the writing “Fuse & Relays.”
Open the fuse box. There you can see a lot of fuses and relays.
On the back of the fuse box cover, there’s a layout diagram that shows which fuse and relay control what. Locate the “HAZ” fuse (Hazard). Typically it’s a 15A fuse.
Pull the fuse out and observe it.
The image below shows what a blown-out fuse would look like. If your Toyota Tundra’s turn signal fuse has blown out, please replace it with a similar amperage fuse (typically 15A).
After replacing it, your indicators should start working.
If you don’t have a fuse handly, here’s a quick diagnosis that will confirm whether the fuse is the primary source of the problem.
Put the key in your Tundra and turn on all electricals. But don’t turn on the engine.
Now, on the fuse box, remove the “HAZ” fuse and replace it with another same amperage fuse from another location in the fuse box.
Now, turn on the left turn signal first. Then the right turn signal.
If the new fuse makes your turn signal work again, it proves your “HAZ” fuse was the primary source of the problem.
However, if the test Fuse blows out immediately, there is a short circuit along the indicator wire, or one of the indicator bulbs is bad and pulling too much power.
If it doesn’t blow out, put the working fuse in its original location and buy a fuse from Walmart, NAPA, or Autozone. You can order fuses from Amazon too.
“GAUGE NO. 1” fuse
If the “HAZ” fuse is okay, please check the “GAUGE No. 1” fuse. It’s inside of your Tundra fuse box below the steering wheel. If it’s blown out, change it with a similar amperage fuse.
Please remember that if the fuse has blown out, the problem isn’t the fuse but something else. Probably the bulb is drawing more current than required. It’s why it causes the fuse to blow out.
In this case, not only the fuse, but we also have to change the turn signal bulb in the Toyota Tundra.
Have you recently been in a minor accident that pulled your front bumper or rear light assembly outward?
Sometimes, a minor tug on the bumper pulls the lighting connection. The wire connecting to a Toyota Tundra’s turn signal is flimsy and breaks easily.
If the lights have not burnt out, the fuse is okay; possibly, the wire that connects the turn signal bulb has broken in some place.
Moreover, these wires are fragile and can break easily for various reasons.
Emergency Flasher Switch Is Broken
It’s rare, but sometimes the hazard switch can get damaged due to age. If the left or right turn signal is working, but the four-way flasher isn’t working, you need to change the hazard switch.
You can buy the switch on either eBay or from a junkyard and change it yourself. Alternatively, you can take your Tundra to a Toyota service center.
Turn Signal Lights Assembly Got Damaged
The turn signal lights don’t always stay on. Still, these lights get hot and can damage the socket. Moisture and water can also cause short circuits.
In some situations, a damaged light socket could also be the source of the problem for a non-working turn signal.
While changing the indicator bulb, please observe the socket for any possible damage. Please take your Tundra to a Toyota service center if there is any damage because we need a new turn signal socket.
Turn Signal Assembly Damaged
It’s rare, but in some cases, probably the entire turn signal controller on the steering wheel may not be working, which in turn makes the turn indicators not work.
If all the lights — turn signal, daytime running lights, headlights, high beams — aren’t working, your turn signal assembly on the steering wheel column has been somehow damaged.
If this happens, you must immediately take your Tundra to the nearest Toyota Service center. It’s a safety hazard to drive without lights, especially at night.
How do I know if the blinker fuse in my Toyota Tundra is bad?
You can quickly diagnose whether the turn signal fuse has blown out. If all the turn signal lights are not working, it means the blinker fuse has gone out.
The fuse is in the engine compartment fuse box. Typically it’s a 15A fuse, and you can purchase it from Walmart, AutoZone, Advance Auto Parts, or NAPA.
What Causes the Turn Signal on Toyota Tundra Stop Working?
The primary reason for having a non-working turn signal in Toyota Tundra is the indicator bulb has burnt out, or the fuse has blown out.
If one of the turn signals is blinking very fast or making a fast clicking sound, one of your indicator bulbs has gone out.
How much does fixing the turn signal on a Toyota Tundra cost?
Changing the turn signal bulb or fuse in your garage would cost less than $5. The fuse and indicator bulbs are cheap and sold at all auto shops such as NAPA, Walmart, or Autozone.
However, if you don’t want to change the turn signal bulb, it would cost around $70 at a Toyota service center or $20-$30 at roadside auto shops.